How To Make Amazing Stable RC Trainer Airplane With Handmade RC. Long Flight Time

How to make a model airplane that can fly very stable with Handmade remote control.
It is a model that is especially suitable for beginners. The fact that it is very stable, can take off from a short distance and provides a long flight time makes it a good trainer model. And it is relatively low cost…
It has a long flight time as it can fly at very low speeds with a small engine power. It can fly at a stable and reasonable speed, usually in the 32% – 45% gas range.
I performed the flight tests (3S) with 11.1V Lipo. But this model (2S) can also fly with 7.4V Lipo.

Technicial Specifications:

Lenght: 73 cm (28.74 inc)
Wing span: 109 cm (42.91 inc)
Flight weight: About 675 gr
Center of gravity: 4.9-5.5cm from the front of the wing
Required control system: Min. 4 channels, 4 micro servos
Suitable battery: 11.1V 2200Mah (Max 2700maH)
Suitable motor: 2212 Brushless Motor (980-1400KV)
Suitable propeller: 2 Blade 9×6 (9060)
Flight Time: Approximately 30 minutes for an average gas level of 38%
Wing area: 1976 cm2
Vbar: 0.46

Necessary Materials:

2212 980-1000KV Brushless Motor: https://s.click.aliexpress.com/e/_DlonA47  OR  https://s.click.aliexpress.com/e/_DFaCQBX  OR  https://s.click.aliexpress.com/e/_DdcuFpX
9×6 propellers: https://s.click.aliexpress.com/e/_Ddlc7mN
30A Brushless ESC: https://s.click.aliexpress.com/e/_DED8ca7 OR https://s.click.aliexpress.com/e/_DCgZnID  OR   https://s.click.aliexpress.com/e/_DejqVBr
LiPo Battery 11.1V 2200mAh: https://s.click.aliexpress.com/e/_DETy3GD
D57mm wheel (2 pcs): https://s.click.aliexpress.com/e/_DcRKQEv
D30mm Wheel: https://s.click.aliexpress.com/e/_DcRKQEv
Control horns (4 pcs): https://s.click.aliexpress.com/e/_DDCKYlh
Micro servos (4 pcs): https://s.click.aliexpress.com/e/_DlZO8BL
Gold Connectors 3.5mm: https://s.click.aliexpress.com/e/_DmxurfH
Wheel stopper: https://s.click.aliexpress.com/e/_DCcQYir
Y extension cable: https://s.click.aliexpress.com/e/_DegReWn
Adjustable Linkage stopper (Easy Link): https://s.click.aliexpress.com/e/_Dkvqb51
Pushrods: https://s.click.aliexpress.com/e/_DFasUR7
Canopy Hatch Lock : https://s.click.aliexpress.com/e/_DE3cpQF
Fiber Strips Adhesive Tape (25mm): https://s.click.aliexpress.com/e/_DlMRzRZ
Fastener strip : https://s.click.aliexpress.com/e/_DnNJGjd
Screws (M2.2-2.3) : https://s.click.aliexpress.com/e/_DEvN4J9
M3x30mm screws : https://s.click.aliexpress.com/e/_DCB0FK3
Heat-Shrink: https://s.click.aliexpress.com/e/_DnMQjEj
5mm Kraft Foamboard  (1 plate)
3mm insulation foam (1 plate)
6mm insulation foam (1 plate)

Lipo Battery Charger: https://s.click.aliexpress.com/e/_DF5pqlz OR

Hot melt Glue Gun: https://s.click.aliexpress.com/e/_DkCDXLd OR
https://s.click.aliexpress.com/e/_DnDleen OR https://s.click.aliexpress.com/e/_Dl2EcLt

If you don’t want to use handmade RC:
4 or 6 channel radio control system: https://s.click.aliexpress.com/e/_DkvL2SL OR
https://s.click.aliexpress.com/e/_DduQ3fv OR https://s.click.aliexpress.com/e/_DCPHEVN

Some of the shops that sell Kraft Foam Board:

In the video,
I showed 3 alternatives for the landing gear. The one I use is the 3D printed one. But any landing gear weighing less than 50gr and having similar dimensions can be used. 2.5mm thick steel wire can be used for a handmade landing gear. The link of the 3D landing gear I designed is below.

Landing Gear 3D File:

For this model, I used the 8-channel handmade remote control, the video of which I published before. Of course, only 4 channels are enough for a trainer plane. It provided good and stable control for this type of model. I had no control problems during the flight.
If you do not want to use a handmade remote control, you can fly this model with any 4 channel or higher remote control.